| Home |    Blogs |  Help |  Search |  Login |  Register |   
MatraSport Forum > Each model > Murena > How to renovate motor for electrical windows
 « previous next »
Pages: [1] 2 Print
Author Topic: How to renovate motor for electrical windows  (Read 58734 times)
hru
Sr. Member
****
Posts: 172


Murena Lover :-)


Email
« on: December 21, 2007, 07:46:54 am »
Hi everybody

Has anybody tried to renovate the motor for the electric window ?
Or is the easiest to by a new ?

/Henrik
Logged
Matra Murena 2.2
steve1962
Newbie
*
Posts: 24


Email
« Reply #1 on: December 21, 2007, 08:53:22 am »
mmm,gotta do this myself.i have heard that its best to strip and remove all the old grease and obviously check the motor.maybe theres a chaep replacement motor that fits ???
Logged
phil75
Sr. Member
****
Posts: 105


Matra Passion Member


WWW Email
« Reply #2 on: December 21, 2007, 09:05:33 am »
the mechanism is specific but the engine is similar to that of Renault 9

the mechanism of origin and the engine of origin are not available any more into new
Logged
- Philippe -
Matra Murena 2.2 1983 engine 20000 km
Yamaha R1 2004  9000 km (engine)
VW Golf II 1.8 1990 209000 km
Rover 111 1994 155000 km
hru
Sr. Member
****
Posts: 172


Murena Lover :-)


Email
« Reply #3 on: December 21, 2007, 10:14:04 pm »
I had the motor apart today - see attached pictures I took on the kitchen table (where else to do main repairs :-))

The sinner is the bearing in the bottom - it was complety 'welded' to the shaft of the rotor.

Second picture it is removed.
Below in housing there is a spring/ring that locks the bearing.
I have to find to get this out, to fasten the bearing again.

/Henrik
Logged
Matra Murena 2.2
Anders Dinsen
Administrator
YaBB God
*****
Posts: 3232



Email
« Reply #4 on: December 22, 2007, 08:15:12 am »
Quote from: hru on December 21, 2007, 10:14:04 pm
I had the motor apart today - see attached pictures I took on the kitchen table (where else to do main repairs :-))

Very insteresting. Is there any space to fit a small ball bearing down there?
Logged
1982 Talbot Matra Murena 2.2 prep 142 (under restoration)

Used to own:
2001 Renault Matra Grand Espace "The Race" V6 24v
1997 Renault Matra Espace 2.0 8V
1987 Renault Matra Espace J11 2.2
krede
YaBB God
*****
Posts: 1172



Email
« Reply #5 on: December 23, 2007, 07:58:09 am »
Quote
Very insteresting. Is there any space to fit a small ball bearing down there?

Ball bearing for a window motor?... sounds a bit like "over kill" to me ;)

If you mess it up and ruin the motor (like I almost certainly would :D ) I belive they are lifted straight from a Talbot Tagora... might help if you end up looking for a new one.
« Last Edit: December 23, 2007, 08:00:23 am by krede » Logged
FOB
Jr. Member
**
Posts: 47


83 Murena 2.2


Email
« Reply #6 on: December 23, 2007, 10:08:21 am »
Hi Henrik, I had the same problem, and I did cut off the small end off the housing and made a new bearing off brass,
it works fine for a ½ year now.

 :) Finn
Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 3232



Email
« Reply #7 on: December 23, 2007, 10:27:08 am »
Quote from: krede on December 23, 2007, 07:58:09 am
Quote
Very insteresting. Is there any space to fit a small ball bearing down there?

Ball bearing for a window motor?... sounds a bit like "over kill" to me ;)

But they are just a few kr... nothing compared to the cost of my labor ;)
Logged
1982 Talbot Matra Murena 2.2 prep 142 (under restoration)

Used to own:
2001 Renault Matra Grand Espace "The Race" V6 24v
1997 Renault Matra Espace 2.0 8V
1987 Renault Matra Espace J11 2.2
hru
Sr. Member
****
Posts: 172


Murena Lover :-)


Email
« Reply #8 on: December 23, 2007, 11:51:02 am »
Ball bearings are only for torque forces, but in this case all forces are in the axiel direction.
The weight of the window is transferred to the axel (the gearbox has no bearings for this)

There is a small plastic piece in the end of the rotor axel - this takes all the forces to outer chasis of the motor.

I have cut a little in the photos, so you can see better.
Logged
Matra Murena 2.2
hru
Sr. Member
****
Posts: 172


Murena Lover :-)


Email
« Reply #9 on: December 23, 2007, 11:53:26 am »
Quote from: FOB on December 23, 2007, 10:08:21 am
Hi Henrik, I had the same problem, and I did cut off the small end off the housing and made a new bearing off brass,
it works fine for a ½ year now.

 :) Finn

Hi Finn

Do you happen to have som photos ?
I might do the same here.

/Henrik
Logged
Matra Murena 2.2
michaltalbot
YaBB God
*****
Posts: 566



Email
« Reply #10 on: December 23, 2007, 05:35:57 pm »
And what about the Simca 1308/Talbot 1510/Solara motors??? Are the exchangeable?
Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 3232



Email
« Reply #11 on: December 24, 2007, 07:43:25 am »
Quote from: hru on December 23, 2007, 11:51:02 am
Ball bearings are only for torque forces, but in this case all forces are in the axiel direction.

Correct though most ball bearings can take axial forces by design.
Logged
1982 Talbot Matra Murena 2.2 prep 142 (under restoration)

Used to own:
2001 Renault Matra Grand Espace "The Race" V6 24v
1997 Renault Matra Espace 2.0 8V
1987 Renault Matra Espace J11 2.2
FOB
Jr. Member
**
Posts: 47


83 Murena 2.2


Email
« Reply #12 on: December 28, 2007, 06:24:41 pm »
Hello Henrik, sorry for the delay, I have no photos, but I have a simple sketch drawn with a shaking hand  ;)
hope that can be a help to you.



- Finn
« Last Edit: April 20, 2008, 09:44:37 am by FOB » Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 3232



Email
« Reply #13 on: December 28, 2007, 10:24:11 pm »
Nice drawing, thanks for sharing it!

The three M3 holes are for screws pushed into the remaining part of the motor housing, I suppose. To attach the new bearing?

Simple, and probably useful to others. What will they cost a piece ;) ?

- Anders
« Last Edit: December 28, 2007, 10:32:02 pm by Anders Dinsen » Logged
1982 Talbot Matra Murena 2.2 prep 142 (under restoration)

Used to own:
2001 Renault Matra Grand Espace "The Race" V6 24v
1997 Renault Matra Espace 2.0 8V
1987 Renault Matra Espace J11 2.2
hru
Sr. Member
****
Posts: 172


Murena Lover :-)


Email
« Reply #14 on: December 29, 2007, 08:27:37 pm »
Quote from: FOB on December 28, 2007, 06:24:41 pm
I have no photos, but I have a simple sketch drawn with a shaking hand  ;)

Hi Finn

Thanks for  the drawing !
It's a nice and easy solution, I think.

I had all parts out, except the locking ring.
To solve it, I drilled a small hole Ø3 in the angled side of the house.
After this, I could get the ring out and also reuse it.

see photo attached.

/Henrik
« Last Edit: December 29, 2007, 08:30:19 pm by hru » Logged
Matra Murena 2.2
Pages: [1] 2 Print 
« previous next »
Jump to: