Anders Dinsen
Administrator
YaBB God
Posts: 3186
WWW
|
|
« Reply #15 on: August 16, 2007, 03:29:09 pm » |
|
No, this number of wires is not original Original electric is very simple in comparison to the other cars, and absolutely doesn't look as chaotic as it does on Your car. I think that somebody who changed Your generator is responsible for Your problem... But You can also use the engine electric from Tagora 2,2 it is the same. I know, that was also what Carjoy told me when they installed a new generator, that the previous installation was a mess. They tried to fix it, but I am a bit disappointed they didn't offer me to replace the wiring loom. I don't mind paying 100 Euro more for a repair bill, if it saves me from lots of trouble later Electrics can take a lot of time, so I doubt if it can be done that cheap Mmmm... the schematics Bart pointed to, are from an early 1.6 (with vacuum warning light instead of choke warning light and a different oil level warning system). It looks like there a fault in the original drawing, too. I can remember Roy said that in the past.
You can't use a diagram for the 1.6, but Lennart has put a reasonably correct 2.2 diagram in the Murena vault on this site: http://www.matrasport.dk/Cars/Murena/vault/Until you get your handy quality controlled diagram from Roy, this will help you What electrical connections are there in the engine bay? It mustn't be that hard I guess? Thick wiring (excess of 50A) to: 1. starter motor 2. generator
These two are one fat wire directly to/from the battery. Never fuse this! Thinner wiring to 1. generator (for the dashboard warning light) 2. ignition circuit (coil and module), and a wire to/from the Hall sensor on the flywheel I think?
Only +12V from the ignition key (circuit 10). 3. carburettor solenoid (but that one may as well go to the ignition circuit)
Yes, that's wired to the ignition. 4. oil pressure sensor 5. coolant temperature sensor
Yes. 6. fuel level and low fuel indicator 7. rear window heater relay feed, rear window heater dashboard warning light and the rear window heater itself (*)
These are seperate and not part of the engine wiring loom. Physically they are routed on the fire wall. and a separate wiring loom to the rear light units. Have I forgotten anything?
Yes: Reversing switch (rear lights) and minus on the ingition coil to drive the rev counter. Where is the oil level sensor of the 2.2 engine located? Is it the sensor in front of the sump? I noticed a sensor there with one wire broken off...
Yes, that's probably it. (*) If the schematics are correct, the rear window heater itself is unfused, only the circuit that feeds the switch, warning light and the relay are protected!
Oh no, there is a fuse, but the diagram is wrong! - Anders
|
|
|
Logged
|
1982 Talbot Matra Murena 2.2 prep 142 2017 BMW i3 "Charged Professional" 94Ah
Used to own: 2001 Renault Matra Grand Espace "The Race" V6 24v 1997 Renault Matra Espace 2.0 8V 1987 Renault Matra Espace J11 2.2
|
|
|
|
brinkie
Jr. Member
Posts: 49
Previous owner of a Murena
WWW
|
|
« Reply #17 on: August 17, 2007, 12:12:15 pm » |
|
And this is CC6, which is the one that carries the ignition circuit (#10):
And this is how CC6 looks on my car (mobile phone image): So I think this is the strategy I will follow: 1. Replace connector CC6 in the front. 2. Replace connector MC2 in the engine bay. 3. Replace wire #10 (switched +) throughout the car where necessary (just disconnect it and run a separate cable in parallel) 4. Check wire #1 (permanent +) for damage also 5. Try and clean up the mess around the generator... 6. Remove, clean and re-fit all earthings (110, 110A, 110B, ...) I am not going to replace wire #10 everywhere, just the part that was hurt by the short circuit 2 years ago, which should have been replaced then! For the winter, I think I am going to remove the dashboard and replace/repair the wiring inside, since it is quite a mess there as well. Some idiot made a separate switch and ran a separate wire for the windscreen washer instead of finding the fault and leave the original wiring! Also, I am studying on a new fuse board, because that is a source of trouble on all Murenas. There are many things I don't understand that are left out (well, of course I understand: cost cutting), e.g. a relay switching the #10 wire instead of the ignition key, leaving the headlights unfused, etc. After this operation is complete, I think I am quite near becoming a Matra Murena electrics guru Cheers, Robert.
|
|
|
Logged
|
/Robert
Previous owner of a Matra Murena 2.2 (1981)
|
|
|
Anders Dinsen
Administrator
YaBB God
Posts: 3186
WWW
|
|
« Reply #18 on: August 18, 2007, 10:52:30 am » |
|
Hi Robert Yes, that's corrosion. It happens when a large constant current flows in an electric circuit and moisture gets into the housing. It's working the reverse of a battery, so to speak. When the connectors then start corroding, the resistance increases and heat builds up. That's why the housing is slightly burnt. The best way to prevent it is to clean and grease the connectors well. I haven't found connector mouldings that fit in the original cutouts. The original male connectors have some very nice tabs that fit into the cutouts, but if the old mouldings are okay, it's quite easy to replace the terminals with new ones. This will preserve the original look. The rubber around the connectors doesn't help much, in my opinion it's better to leave them open, but the grease the whole connector inside and outside before putting them together. These are available at VWP in both male and female types and they fit directly into the old mouldings: http://www.vehicle-wiring-products.eu/VWP-onlinestore/terminalsnonins/noninsblades.php. About the ignition lock: It is designed to switch a very large current, so if everything is okay, I don't see the advantage of fitting a relay instead. The windows are switched by a relay, however, probably because their current consumption exceeds the maximum allowable over the lock. That said, however, I will fit a 70A relay on my Murena since I've had some problems with the connections to the ignition lock getting very hot and melting. I'm going to fit a new ignition circuit directly from the battery over a high current fuse to the relay, and fit the relay under the dash. I will also fit a few new fuses for radio and auxillary power outlet for my mobile phone and GPS. My radio is in need of a better power supply, so that will help there too. Fuses are good and bad. Reliability wise, they introduce an additonal potetially weak link. But they are excellent fault finding tools. I "fell in love" with this modular unit some time ago, but recently it has moved down my wish list as the old fuse board works well enough as it is. After all, it only powers "uncritical" consumers. Parts are also available from VWP, but the product is from Ripaults AFAIK. - Anders
|
|
« Last Edit: August 18, 2007, 11:30:19 am by Anders Dinsen »
|
Logged
|
1982 Talbot Matra Murena 2.2 prep 142 2017 BMW i3 "Charged Professional" 94Ah
Used to own: 2001 Renault Matra Grand Espace "The Race" V6 24v 1997 Renault Matra Espace 2.0 8V 1987 Renault Matra Espace J11 2.2
|
|
|
|
|
roy4matra
YaBB God
Posts: 1200
|
|
« Reply #21 on: August 25, 2007, 01:59:19 pm » |
|
Please careful if you use these diagrams (1.6 and 2.2) as there are many mistakes in them. Oh no, there is a fuse, but the diagram is wrong! - Anders
The official workshop manual wiring diagrams had mistakes in them; someone copied them and made those crude diagrams AND added more mistakes, and someone put some diagrams on a CD which Delcourt once sold, and there are even more mistakes on those! This was why I spent many hours making my own Murena wiring diagrams which also cover most variations. Did you know for instance that the first 1.6 Murena models had the instruments lit all the time the ignition was on (like the Bagheera)? They are not switched on when you switch the sidelamps on, which is why you have a sidelight warning light in the instrument panel. You need it to know when the lights are on, because the instrument lights being on mean nothing concerning outside lights unlike a normal system. There are variations not only between 1.6 and 2.2 but between early and late cars, normal French spec. and German spec. owing to different laws in those countries, and the original diagrams lack much information about the real looms. Where is the 82 ohm resistor for instance and why is it there? My diagrams include all the information and they are accurate. They are obviously only as standard so if your car has had alterations or additions, then you should keep notes of these, or whoever did the modifications should have made them. Unfortunately, often that never happens which leads to problems with the subsequent owners! At least the Murena is quite a simple car, and the wiring is easy to work out if you know electrics. Roy
|
|
|
Logged
|
|
|
|
brinkie
Jr. Member
Posts: 49
Previous owner of a Murena
WWW
|
|
« Reply #22 on: August 25, 2007, 10:10:59 pm » |
|
This was why I spent many hours making my own Murena wiring diagrams which also cover most variations. Did you know for instance that the first 1.6 Murena models had the instruments lit all the time the ignition was on (like the Bagheera)? They are not switched on when you switch the sidelamps on, which is why you have a sidelight warning light in the instrument panel. You need it to know when the lights are on, because the instrument lights being on mean nothing concerning outside lights unlike a normal system.
My company car (Astra) and my girlfriend's Citroën C3 have the same "feature", the instrument lights switch on with the ignition and there is a green indicator light when the sidelamps have been switched on. So it's not only the early Murena At least the Murena is quite a simple car, and the wiring is easy to work out if you know electrics.
Unfortunately, the people who worked on my car (even a "Matra specialist") didn't know **** about electrics. Today, I worked hours on my car's electrical system, to repair the short circuit and the bad connections, which kept the engine from running. I have to admit: it is a very simple car to work on, once you have the car on a lift. First I started measuring voltages at the diagnostic connector on top of the engine. I bypassed the ignition switch and connected the #10 wire after the "CC6" connector under the front hood. The voltage from the #3 wire was 11,8V (the battery was heavily drained during the two months standstill as I noticed later), but the voltage from the #10 wire was only 10,8V, so there was a 1V voltage drop! I raised the car on a lift and took a look at the "MC2" connector in the engine bay. I took the male and female parts of the connectors apart and... one of the connectors literally fell apart! I turned out that a very crude repair has been done to the lower part of the connector (the one that goes to the front of the car) and that the wiring loom there has been left untouched after the first short circuit, two years ago. The #10 wire which was coming from the main wiring loom was almost "naked" and heavily corroded. This can only be seen from below, but it was clearly a time bomb! If I am correct, through this MC2 connector are the following leads running: #94 temperature sensor #90 oil pressure sensor #15 tacho signal #10 switched +12V from the ignition key #14 switched +12V from the ignition key in the "start" position #9 charging indicator I ran a bypass #10 cable along the main wiring loom, from the ignition switch to the engine wiring loom. Also, I connected the #9 and #14 from the engine wiring loom to the original main engine loom. Then I tried to start the engine and it did fire once, before the battery went dead So I charged the battery a bit and after half an hour I tried to start the engine again: VRROUMMMMM!!!! Yee-haaa!!! The engine is running again! Now I have to complete the task. First, the battery charging light is still not working (and the bulb isn't broken), so I think I will directly connect the #9 wire to the generator, instead of having it running around the wiring loom. Second, I have to find a decent way to re-fit all the other wiring going through those half molten connectors. And, of course. clean up the wiring mess around the generator. But I am confident I will bring this task to a succesful end
|
|
|
Logged
|
/Robert
Previous owner of a Matra Murena 2.2 (1981)
|
|
|
roy4matra
YaBB God
Posts: 1200
|
|
« Reply #23 on: August 26, 2007, 08:43:24 am » |
|
...Now I have to complete the task. First, the battery charging light is still not working (and the bulb isn't broken), so I think I will directly connect the #9 wire to the generator, instead of having it running around the wiring loom. Second, I have to find a decent way to re-fit all the other wiring going through those half molten connectors. And, of course. clean up the wiring mess around the generator. But I am confident I will bring this task to a succesful end I am sure you will Robert, but be careful with the charging system. You must not bypass the 82 ohm resistor. It is necessary for the charging system to work correctly. An alternator must have a certain current to initally energise. Once charging they self energise. The warning light used to be large enough to provide this current, but with the newer smaller bulb that the Bagheera and Murena uses it is no longer enough. So Matra used a resistor in parallel to the bulb to provide the total current. Your list for the MC2 connector is correct. Roy
|
|
« Last Edit: August 26, 2007, 08:47:34 am by roy4matra »
|
Logged
|
|
|
|
brinkie
Jr. Member
Posts: 49
Previous owner of a Murena
WWW
|
|
« Reply #24 on: August 26, 2007, 10:59:50 pm » |
|
I am sure you will Robert, but be careful with the charging system. You must not bypass the 82 ohm resistor. It is necessary for the charging system to work correctly. An alternator must have a certain current to initally energise. Once charging they self energise. The warning light used to be large enough to provide this current, but with the newer smaller bulb that the Bagheera and Murena uses it is no longer enough. So Matra used a resistor in parallel to the bulb to provide the total current.
Where is that 82 ohm resistor located Roy? Is it in the instrument panel, or is it fitted somewhere near the alternator? I can't seem to find it on the schematics, but this may just be one of the many faults in them Cheers, Robert
|
|
|
Logged
|
/Robert
Previous owner of a Matra Murena 2.2 (1981)
|
|
|
|
brinkie
Jr. Member
Posts: 49
Previous owner of a Murena
WWW
|
|
« Reply #26 on: August 27, 2007, 10:53:53 am » |
|
Where is that 82 ohm resistor located?
Look carefully at the plug on the back of the instrument panel. OK, then there is no problem, since I am only re-routing the cable up till and including the connector under the front hood. The rest of the #9 cable seems fine. I should be able to check whether the cable is good, since switching on the ignition without starting the engine should give a positive voltage to the #9 terminal. Is the 82 ohm resistor inside the plug (i.e. combined with the light bulb) or is it part of the printed circuit? I have swapped some of the light bulbs to check whether the light was gone just because the bulb was broken.
|
|
|
Logged
|
/Robert
Previous owner of a Matra Murena 2.2 (1981)
|
|
|
Anders Dinsen
Administrator
YaBB God
Posts: 3186
WWW
|
|
« Reply #27 on: August 27, 2007, 11:19:55 am » |
|
Is the 82 ohm resistor inside the plug (i.e. combined with the light bulb) or is it part of the printed circuit? I have swapped some of the light bulbs to check whether the light was gone just because the bulb was broken.
No it's on the plug itself. Roy, woult you think the resistor is necessary in parallel with the bulb to get the alternator regulator started, or is it to ensure that it can start even if the bulb blows? Robert, In case the wiring is broken to the alternator, you will get charging problems. Just a thought... maybe you had the alternator replaced only because of bad wiring and not because of a problem in it? I think newer regulators are able to start even without the charge warning light not wired.
|
|
|
Logged
|
1982 Talbot Matra Murena 2.2 prep 142 2017 BMW i3 "Charged Professional" 94Ah
Used to own: 2001 Renault Matra Grand Espace "The Race" V6 24v 1997 Renault Matra Espace 2.0 8V 1987 Renault Matra Espace J11 2.2
|
|
|
brinkie
Jr. Member
Posts: 49
Previous owner of a Murena
WWW
|
|
« Reply #28 on: August 27, 2007, 11:15:21 pm » |
|
Roy, woult you think the resistor is necessary in parallel with the bulb to get the alternator regulator started, or is it to ensure that it can start even if the bulb blows?
Robert, In case the wiring is broken to the alternator, you will get charging problems. Just a thought... maybe you had the alternator replaced only because of bad wiring and not because of a problem in it?
I think newer regulators are able to start even without the charge warning light not wired.
Hmmm... - when I bought the car, the warning light wasn't working, I never bothered to repair - the first year I had to replace the battery, after half a year I had to replace the battery again - three years later the alternator has been replaced because I was told it wasn't charging well - the charging light worked fine after that - three weeks later a short circuit almost set fire to my car, it was repaired under warranty - two years later, just before the second short circuit, the charging warning light quit again I will check the resistance tomorrow with a digital multimeter, if it reads somewhere around 82 ohm (give or take 10%) it must be OK.
|
|
|
Logged
|
/Robert
Previous owner of a Matra Murena 2.2 (1981)
|
|
|
|