Title: 3.0 v6-24 Engine stalls when cold.
Post by: Trolkar on October 04, 2009, 11:38:46 am
Hi there!
Over the past few days, where the temperature is around 4-8 Celsius, I have some problems with my engine.
It runs fine, and the rev is a bit higher than normal. But it suddenly just stalls. Mainly after a short stop in the traffic (red light e.g.) and when the accelerator is pressed, the engine just stalls.
If running in n the engine starts up with a high rev, and slowly drops into normal rev. And then after 1 or 2 min. it just stalls
After the engine has stalled, it is very heard to start again.
The starter has to run for about 5--20 sec. and the accelerator has to be pressed down slowly. After it starts, it reacts like an old engine which chokes in petrol.
This way of starting the engine also happens when I have to start then engine and it is warm.
What is wrong, and are there a link between the errors?
Over the past few days, where the temperature is around 4-8 Celsius, I have some problems with my engine.
It runs fine, and the rev is a bit higher than normal. But it suddenly just stalls. Mainly after a short stop in the traffic (red light e.g.) and when the accelerator is pressed, the engine just stalls.
If running in n the engine starts up with a high rev, and slowly drops into normal rev. And then after 1 or 2 min. it just stalls
After the engine has stalled, it is very heard to start again.
The starter has to run for about 5--20 sec. and the accelerator has to be pressed down slowly. After it starts, it reacts like an old engine which chokes in petrol.
This way of starting the engine also happens when I have to start then engine and it is warm.
What is wrong, and are there a link between the errors?
Title: Re: 3.0 v6-24 Engine stalls when cold.
Post by: Anders Dinsen on October 04, 2009, 02:08:48 pm
Water temperature sensor is defective!
This is a well known problem on this engine. Just replace it and the trouble will be cured! A diagnosis will tell you the lambda sensor is defective, but it's not. I have no idea why these sensors have a tendency to fail, but they just do....!
/Anders
This is a well known problem on this engine. Just replace it and the trouble will be cured! A diagnosis will tell you the lambda sensor is defective, but it's not. I have no idea why these sensors have a tendency to fail, but they just do....!
/Anders
Title: Re: 3.0 v6-24 Engine stalls when cold.
Post by: Trolkar on October 04, 2009, 06:29:43 pm
Great! - Thanks for the reply!
How much is a new sensor?!? - And is it hard to change?
Where is it locatet?
How much is a new sensor?!? - And is it hard to change?
Where is it locatet?
Title: Re: 3.0 v6-24 Engine stalls when cold.
Post by: Anders Dinsen on October 04, 2009, 06:39:55 pm
Sensors tend to be expensive, and I would personally only trust a genuine Renault part.
It's easy to replace, though. It's the one with the green connector on the photo below. You will need to remove the air filter housing to get proper access.
/Anders
(http://gallery.dinsen.net/d/4926-2/DSCF0006_001.JPG)
It's easy to replace, though. It's the one with the green connector on the photo below. You will need to remove the air filter housing to get proper access.
/Anders
(http://gallery.dinsen.net/d/4926-2/DSCF0006_001.JPG)
Title: Re: 3.0 v6-24 Engine stalls when cold.
Post by: Trolkar on October 08, 2009, 09:07:33 pm
One genuine sensor is on the way!...
The error was as you wrote, lambda but also the water temp. sensor.
Is it possibly to change without draining the coolingsystem?
The error was as you wrote, lambda but also the water temp. sensor.
Is it possibly to change without draining the coolingsystem?
Title: Re: 3.0 v6-24 Engine stalls when cold.
Post by: renaultbiler on October 08, 2009, 09:38:47 pm
The lambda fault is always present on this car - i think its more like a software design problem.
You can change sensor without draining the cooling system.
You can change sensor without draining the cooling system.
Title: Re: 3.0 v6-24 Engine stalls when cold.
Post by: Anders Dinsen on October 08, 2009, 10:03:03 pm
The lambda fault is always present on this car - i think its more like a software design problem.
;D
Quote
You can change sensor without draining the cooling system.
I agree. Some water will flow out of the hole, but not a lot, so it shouldn't cause any problems.
/Anders
Title: Re: 3.0 v6-24 Engine stalls when cold.
Post by: Trolkar on November 23, 2009, 08:24:30 am
Hi there!
Sorry for the late reply! Work is "almost" killing me :-\
I managed to change the sensor. My biggest problem was to get the tiny metal clips off.
After replacing, the engine runs just fine! It havent stalled since!
15 min. of work, and a sensor a 435 Dkr. Around 58 Eur.
Thank you SO much for your help!
Sorry for the late reply! Work is "almost" killing me :-\
I managed to change the sensor. My biggest problem was to get the tiny metal clips off.
After replacing, the engine runs just fine! It havent stalled since!
15 min. of work, and a sensor a 435 Dkr. Around 58 Eur.
Thank you SO much for your help!
