Title: Espace III oil pressure sensor
Post by: bigpaul on November 11, 2009, 11:14:42 pm
I have had a diagnostic on my car (1999 3.0 V6) which has shown that the oil pressure sensor/switch has failed.
In order to try and keep costs down I am looking to source and fit a new item myself. Having now located a part can anyone offer me advise on where the sensor/switch is located on the engine?
I have seen a previous post regards an item located above the oil filter. Can anyone confirm this please?
Thanks
BigPaul.
In order to try and keep costs down I am looking to source and fit a new item myself. Having now located a part can anyone offer me advise on where the sensor/switch is located on the engine?
I have seen a previous post regards an item located above the oil filter. Can anyone confirm this please?
Thanks
BigPaul.
Title: Re: Espace III oil pressure sensor
Post by: Anders Dinsen on November 12, 2009, 10:25:54 pm
Hi BigPaul
The pressure switch shouldn't be too difficult to find, but being in Denmark I can't really help you.
I think, however, that I can help with advice on locating the switch. It is indeed located above the oil filter, a bit near the front (belt end) of the engine. Look at this photo, where you will can see a part of the switch behind the cable to the starter. It's an area of the engine which is easily accessible from underneath the car, so it shouldnt' be hard to replace. The oil level sensor is next to the switch (to the right).
(http://gallery.dinsen.net/d/12752-4/DSC_8941.JPG)
/Anders 8)
The pressure switch shouldn't be too difficult to find, but being in Denmark I can't really help you.
I think, however, that I can help with advice on locating the switch. It is indeed located above the oil filter, a bit near the front (belt end) of the engine. Look at this photo, where you will can see a part of the switch behind the cable to the starter. It's an area of the engine which is easily accessible from underneath the car, so it shouldnt' be hard to replace. The oil level sensor is next to the switch (to the right).
(http://gallery.dinsen.net/d/12752-4/DSC_8941.JPG)
/Anders 8)
Title: Re: Espace III oil pressure sensor
Post by: bigpaul on November 14, 2009, 12:54:10 pm
Thanks Anders.
The oil switch and water temperature sensor were very easy to change, considering its a Renault!!
Touch wood the car is running better than ever at the moment. Starts straight away.
The whole job took less than 30minutes.
Paul.
The oil switch and water temperature sensor were very easy to change, considering its a Renault!!
Touch wood the car is running better than ever at the moment. Starts straight away.
The whole job took less than 30minutes.
Paul.
Title: Re: Espace III oil pressure sensor
Post by: Anders Dinsen on November 14, 2009, 08:28:02 pm
That's very good to hear, Paul :)
The water temperature sensor can make a real mess on this enigne. For some reason they have a tendency to fail. It usually only causes cold-running problems, but it can also cause warm-running problems. On my car, the sensor had periodic problems and luckily failed once while the garage had the car on diagnostics computer. Suddenly the engine would start running rough in idle and the water temperature show -40 degrees or so. A moment later it would be back to normal. Replacing the sensor fixed the problem.
Yes, french cars can be a pain to work on. But they look better than other cars! :)
Cheers,
Anders
The water temperature sensor can make a real mess on this enigne. For some reason they have a tendency to fail. It usually only causes cold-running problems, but it can also cause warm-running problems. On my car, the sensor had periodic problems and luckily failed once while the garage had the car on diagnostics computer. Suddenly the engine would start running rough in idle and the water temperature show -40 degrees or so. A moment later it would be back to normal. Replacing the sensor fixed the problem.
Yes, french cars can be a pain to work on. But they look better than other cars! :)
Cheers,
Anders
Title: Re: Espace III oil pressure sensor
Post by: renaultbiler on November 15, 2009, 10:50:39 pm
were very easy to change, considering its a Renault!!
Thats just an old fairytale - ive worked on many makes of cars and find the Renault equal or better to work on in general. I think when the R16 came with the engine and gearbox mounted the wrong way it created a virtually non-reversible statement on Renault and their headless constructions.
i'm much more comfy with working on Renaults rather than many other "accepted" car makes ;D
