| Home  Blogs Help Search Login Register  
« previous next »
Pages: [1] Print
Author Topic: new owner in kent  (Read 899 times)
tonyz59
Newbie
*
Posts: 5


« on: August 13, 2019, 04:58:45 pm »

Just thought I'd say Hi,  just recently bought a 2.2 murena in silver with grey  buttoned velour interior ! going to be  a running and hopefully !! only a tinkering project. It has the usual slow electric windows, especially the passenger side. Also the 2nd speed on the wipers is not much faster than no 1.  managed to source the passenger door mirror off of ebay that was broken, so a few little jobs done already. This is not my 1st matra as I had a orange bagheera  s  37 years ago, funnily enough the age of the murena . Tony
Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 2993



WWW
« Reply #1 on: August 13, 2019, 09:59:08 pm »

Hi Tony, congratulations on your Murena - I hope you'll have many years of fun with tinkering and driving. It would be lovely if you could share some pictures of it. Welcome here!

/Anders
Logged

'82 Murena 2.2 prep 142
'01 Grand Espace 24v
'08 Smart Fortwo 0,8 cdi
tonyz59
Newbie
*
Posts: 5


« Reply #2 on: October 16, 2019, 01:23:09 pm »

Some photos maybe ! car is up on ramps and stands due to cooling issues. At first thought it was the pump but after further investigating turns out there is a new pump on the car. the problem was a faulty stat a seeping hose on the cooling pipe at the engine end and a completely worn out fan belt. Having ordered some new hoses for the engine to coolant pipes, I started to replace them, unfortunately it turns out the pipes that run down the engine are corroded and holed where the hose clamps to them. Also the front to rear are in a similar state and the heater pipes had been replaced with 15mm copper tube at some point in the past ! so my cheap fix of a new stat and 2 new hoses has escalated into ordering new pipes !

On reading previous posts on this subject removing the front wheel/ battery molding will give me better access to fit the pipes ? I guess with so much rust in the system it will pay to do this and remove the rad and give it a thorough flush through.

« Last Edit: October 16, 2019, 07:46:20 pm by Anders Dinsen » Logged
tonyz59
Newbie
*
Posts: 5


« Reply #3 on: October 16, 2019, 01:28:20 pm »

better photos resized hopefully !  Roll Eyes
« Last Edit: October 16, 2019, 07:46:39 pm by Anders Dinsen » Logged
tonyz59
Newbie
*
Posts: 5


« Reply #4 on: October 16, 2019, 01:33:51 pm »

looks like i have not mastered the uploading o photos  Roll Eyes
« Last Edit: October 16, 2019, 07:47:16 pm by Anders Dinsen » Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 2993



WWW
« Reply #5 on: October 16, 2019, 07:43:55 pm »

Some photos maybe ! car is up on ramps and stands due to cooling issues. At first thought it was the pump but after further investigating turns out there is a new pump on the car. the problem was a faulty stat a seeping hose on the cooling pipe at the engine end and a completely worn out fan belt. Having ordered some new hoses for the engine to coolant pipes, I started to replace them, unfortunately it turns out the pipes that run down the engine are corroded and holed where the hose clamps to them. Also the front to rear are in a similar state and the heater pipes had been replaced with 15mm copper tube at some point in the past ! so my cheap fix of a new stat and 2 new hoses has escalated into ordering new pipes !

On reading previous posts on this subject removing the front wheel/ battery molding will give me better access to fit the pipes ? I guess with so much rust in the system it will pay to do this and remove the rad and give it a thorough flush through.



Hi Tony

Yes, removing the tub for the spare wheel will give you good access. Remove the battery and the ground and plus wires, drill out the rivets (don't forget the small brackets underneath on each side), remove the vacuum actuator and the two connected vacuum pipes, and disconnect the fan (underneath) and unfasten the connector housing from the tub.  You should then have the tub free and should be able to carefully pull it out.

New pipework under the car is a good investment, so don't feel too sorry for having to replace them. Cooling is so important on mid-engined cars, the Murena included. Flushing the rad sounds like a good idea as there will likely be some rust collected in the system.

On your photo of the enigne, I noticed that your reservoir only has two connections, a 16 mm at the bottom and what appears to be a 6 mm on the top. The rad vent looks like it's connected to the top, which is incorrect and can cause problems with air getting being sucked into the rad. A T-piece inserted in the bottom hose should do the job.

https://www.carbuilder.com/uk/black-nylon-stepped-t-piece-1512mm-108mm

About picture uploading. The forum software will not resize your pictures, but display them as uploaded - pixel by pixel. So you need to resize them before uploading. 800 px is a good width. We like the software for many other good reasons and have never gotten around to fix this Smiley

I've taken the liberty to resize your photos Smiley

Best,
Anders
« Last Edit: October 16, 2019, 07:50:26 pm by Anders Dinsen » Logged

'82 Murena 2.2 prep 142
'01 Grand Espace 24v
'08 Smart Fortwo 0,8 cdi
Oetker
YaBB God
*****
Posts: 1085



« Reply #6 on: October 19, 2019, 11:12:18 pm »

Removing give the workspot much better acces.
It's a simple job to get it out.
Logged

I feel like Jonah, only my fish looks different.
Murena 2.2 Red 1982. Murena 1.6 black on places.
tonyz59
Newbie
*
Posts: 5


« Reply #7 on: October 24, 2019, 08:35:17 pm »

 nice pic mate Grin well  after removing all the rusted cooling engine pipes and various botched hoses ! I will be fitting this lot !
« Last Edit: October 24, 2019, 08:51:22 pm by tonyz59 » Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 2993



WWW
« Reply #8 on: October 24, 2019, 09:16:34 pm »

nice pic mate Grin well  after removing all the rusted cooling engine pipes and various botched hoses ! I will be fitting this lot !

Looks great!!
Logged

'82 Murena 2.2 prep 142
'01 Grand Espace 24v
'08 Smart Fortwo 0,8 cdi
Pages: [1] Print 
« previous next »
Jump to: