| Home  Blogs Help Search Login Register  
« previous next »
Pages: [1] 2 Print
Author Topic: Murena 2.2 cylinder head bolts torque settings?  (Read 8820 times)
macaroni
YaBB God
*****
Posts: 533


Murena and Multipla - I like it 3 abreast!


« on: May 29, 2008, 12:34:28 pm »

Can anyone tell me the torque settings for the cylinder head bolts on the 2.2 please?

Cheers,

Antony
Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 2823



WWW
« Reply #1 on: May 29, 2008, 01:56:04 pm »

90 Nm
Logged

'82 Murena 2.2 prep 142
'01 Grand Espace 24v
'08 Smart Fortwo 0,8 cdi
macaroni
YaBB God
*****
Posts: 533


Murena and Multipla - I like it 3 abreast!


« Reply #2 on: May 29, 2008, 02:37:44 pm »

Thank you.
Logged
macaroni
YaBB God
*****
Posts: 533


Murena and Multipla - I like it 3 abreast!


« Reply #3 on: May 29, 2008, 02:59:08 pm »

Can you tell me the valve clearances also please?
Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 2823



WWW
« Reply #4 on: May 29, 2008, 03:29:26 pm »

Can you tell me the valve clearances also please?

No, the manual is back on the shelf again Wink

Okay... here goes:

Inlet: 0.2 mm
Exhaust: 0.3 mm

Cold engine.
Logged

'82 Murena 2.2 prep 142
'01 Grand Espace 24v
'08 Smart Fortwo 0,8 cdi
macaroni
YaBB God
*****
Posts: 533


Murena and Multipla - I like it 3 abreast!


« Reply #5 on: May 29, 2008, 04:01:13 pm »

Thanks again.

Can you also please tell...just joking.

Cheers,

Antony
Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 2823



WWW
« Reply #6 on: May 29, 2008, 04:23:05 pm »

Can you also please tell...just joking.

No, I don't know any jokes! Wink

You're always welcome
Logged

'82 Murena 2.2 prep 142
'01 Grand Espace 24v
'08 Smart Fortwo 0,8 cdi
krede
YaBB God
*****
Posts: 1166



« Reply #7 on: May 29, 2008, 05:04:57 pm »

remember to "pre torque"  all the bolts 5nm, before you go on to fasten them 90 nm.

Also there is a specific sequence you need to torque up the bolts in.
Logged
macaroni
YaBB God
*****
Posts: 533


Murena and Multipla - I like it 3 abreast!


« Reply #8 on: May 29, 2008, 06:07:23 pm »

I just wanted to check them. I did it from the middle, working outwards. They were all tight enough.
I'm going to check the valve clearances next, once it stops raining!
Logged
roy4matra
YaBB God
*****
Posts: 873



« Reply #9 on: May 29, 2008, 08:13:28 pm »

Can anyone tell me the torque settings for the cylinder head bolts on the 2.2 please?

All the engine torque settings are available from my website if you just asked me.  There is a double A4 page taken from the workshop manual.  Valve clearances are in the Murena handbook.

Roy
Logged

macaroni
YaBB God
*****
Posts: 533


Murena and Multipla - I like it 3 abreast!


« Reply #10 on: May 29, 2008, 08:44:08 pm »

I looked, but couldn't find them on there and still can't.

Can you point me at them please?
Logged
roy4matra
YaBB God
*****
Posts: 873



« Reply #11 on: May 29, 2008, 09:12:41 pm »

I looked, but couldn't find them on there and still can't.

Can you point me at them please?

No you won't.  I said 'if you ask'.  If anyone emails me I can send them a link.

Roy
Logged

Anders Dinsen
Administrator
YaBB God
*****
Posts: 2823



WWW
« Reply #12 on: May 29, 2008, 09:55:05 pm »

I just wanted to check them. I did it from the middle, working outwards. They were all tight enough.
I'm going to check the valve clearances next, once it stops raining!

Weather over here is beautiful Tongue
Did you get a chance to identify your cam then?

- Anders
Logged

'82 Murena 2.2 prep 142
'01 Grand Espace 24v
'08 Smart Fortwo 0,8 cdi
macaroni
YaBB God
*****
Posts: 533


Murena and Multipla - I like it 3 abreast!


« Reply #13 on: May 29, 2008, 11:32:35 pm »

Only just stopped raining now!
My car is garaged, but I want it dry so I can roll it in and out in 4th gear to rotate the valvetrain.

I looked at my cam, but couldn't identify it. I'll photo it tomorrow, in the light, and post it up.
Logged
roy4matra
YaBB God
*****
Posts: 873



« Reply #14 on: May 30, 2008, 08:18:33 am »

Can you tell me the valve clearances also please?

Inlet: 0.2 mm
Exhaust: 0.3 mm

Cold engine.

However, that is for the standard cam, Anders.

The Holbay cam has slightly different settings.

The inlets should be: 0.25 mm (10 thou)
Exhausts as original: 0.30 mm (12 thou)

Roy
Logged

Pages: [1] 2 Print 
« previous next »
Jump to: