| Home  Blogs Help Search Login Register  
« previous next »
Pages: [1] 2 3 ... 5 Print
Author Topic: Common failures / preventive parts replacements  (Read 127374 times)
Bart_Maztra
Sr. Member
****
Posts: 211



« on: August 30, 2008, 05:18:59 pm »

What are the common failures and/or what is worth replacing preventive?
Logged

RazorbackNOR
Sr. Member
****
Posts: 494



« Reply #1 on: August 30, 2008, 07:38:12 pm »

What are the common failures and/or what is worth replacing preventive?

Rear trailing arms!!  Shocked
Logged

2010 Mazda 3 1,6  Diesel Gunmetal Blue
1983 Matra Murena 2.2 Platine
50cc Pocketbike
IPSC shooter
suffolkpete
YaBB God
*****
Posts: 544



« Reply #2 on: August 30, 2008, 08:23:04 pm »

Fuse panel printed circuit board connectors. I did the remaining ones on my car recently and the I found that the Rover ones recommended by Roy are getting difficult to obtain.  In the end I got some from a Mini specialist (they are used to connect the ECU on Minis from 1989 onwards) and they said that there would be no more once the existing stocks were gone.  I have searched the catalogues of the major connector manufacturers (AMP etc) to no avail.  I think a lot of Murena owners would be very grateful to anybody who can recommend an alternative.
Logged
krede
YaBB God
*****
Posts: 1172



« Reply #3 on: August 31, 2008, 10:58:34 am »

The fiber inserts in the front suspension arms where the anti roll bar is attached.
And of cause rust proofing.
Logged
Bart_Maztra
Sr. Member
****
Posts: 211



« Reply #4 on: August 31, 2008, 08:29:23 pm »

What about the clutch master cilinder seals and / or break seals?
Logged

Titus
Sr. Member
****
Posts: 145



« Reply #5 on: August 31, 2008, 09:23:06 pm »

What about the clutch master cilinder seals and / or break seals?

Yes, mine has failed, clutch master. It was leaking into the drivers footwell. This done check the slave at the rear. On mine this was also leaking so changed.

It seems that once one part is changed then another fails. So incase the break cylinder was to follow the clutch and fail it was replaced.

And for any 1.6 owners, check your engine mount brackets. One of mine failed whilst on the go. Very scary. The engine drops onto the gear linkages throwing the gear stick violently to the right and leaving you no control over the engine or transmision.
« Last Edit: September 04, 2008, 01:28:14 am by Lennart Sorth » Logged

1.6 Murena
suffolkpete
YaBB God
*****
Posts: 544



« Reply #6 on: September 01, 2008, 06:55:01 pm »

Quote
And for any 1.6 owners, check your engine mount brackets. One of mine failed whilst on the go. Very scary. The engine drops onto the gear linkages throwing the gear stick violently to the right and leaving you no control over the engine or transmision.

I also think it's worth reiterating Roy's advice to check the bolts holding the bracket to the gearbox for tightness as it is movement that causes the bracket to fail.
Logged
Anders Dinsen
Administrator
YaBB God
*****
Posts: 3198



« Reply #7 on: September 02, 2008, 08:26:24 am »

This is an excellent thread! I'll make it 'sticky' so it stays on top of the Murena-subject.

My contribution will be that it's always a good idea to replace distributor cap and rotor before doing any fuelling or ignition maintenance or adjustments. Plugs and leads can be checked and kept if okay, but unless you are on a tight budget, why not replace them with new? The coil should be wiped dry on the top. These are cheap components that can make a significant difference!

Second, get a new set of gaskets for the carburettor and give it a good cleaning with compressed air, WD40, and petrol. A well maintained carburettor don't go wrong, but if any of the fuel and air channels are blocked, it will never perform. On the 2.2, the Solex 34CICF has an O-ring to seal the acceleration pump fuel channel. This O-ring is often incorrectly sized in the gasket kits, and if it's not the right size, fuel will leak out. This can cause running problems!

- Anders
Logged

1982 Talbot Matra Murena 2.2 prep 142 (under restoration)
2017 BMW i3 "Charged Professional" 94Ah
2024 VW id.buzz Pro

Used to own:
2001 Renault Matra Grand Espace "The Race" V6 24v
1997 Renault Matra Espace 2.0 8V
1987 Renault Matra Espace J11 2.2
Anders Dinsen
Administrator
YaBB God
*****
Posts: 3198



« Reply #8 on: September 02, 2008, 08:39:17 am »

Forgot...: Water pump. A leaking pump can't keep water pressure up, so while there may still be a good flow of water through the engine, the water will boil, and boiling water can't absorb heat => Engine will suffer!
Logged

1982 Talbot Matra Murena 2.2 prep 142 (under restoration)
2017 BMW i3 "Charged Professional" 94Ah
2024 VW id.buzz Pro

Used to own:
2001 Renault Matra Grand Espace "The Race" V6 24v
1997 Renault Matra Espace 2.0 8V
1987 Renault Matra Espace J11 2.2
krede
YaBB God
*****
Posts: 1172



« Reply #9 on: September 02, 2008, 10:03:10 am »

I agree with Mr.Diensen..
Ignition parts are "wear" parts just like break pads etc... even the coil should be replaced once in a while.
Logged
matramurena
Sr. Member
****
Posts: 125



« Reply #10 on: September 02, 2008, 06:35:52 pm »

How about Mazda engine-parts? Wink
« Last Edit: September 04, 2008, 01:30:17 am by Lennart Sorth » Logged

1983 Matra Murena V6 (AR engine)
2003 Matra Avantime 2.0T Expression
2003 Matra Avantime V6 Privilege
Bart_Maztra
Sr. Member
****
Posts: 211



« Reply #11 on: September 03, 2008, 06:58:21 am »

The fiber inserts in the front suspension arms where the anti roll bar is attached.
Don't understand Huh

How about Mazda enine-parts? Wink
Don't think mazda engine will qualify as a preventive replacement Cheesy
Logged

Oskar
Sr. Member
****
Posts: 285



« Reply #12 on: September 03, 2008, 04:46:07 pm »

rubbersealing for the doors  Angry Cry
Logged

peugeot 205 gti
murena 1.6
Anders Dinsen
Administrator
YaBB God
*****
Posts: 3198



« Reply #13 on: September 03, 2008, 05:41:48 pm »

While we're at the rubber...:

Water hoses, and the pipes under the car and in the engine room Shocked
Tyres Wink

And since Oskar mentioned the doors: Electric window motors and window mechanisms...
Logged

1982 Talbot Matra Murena 2.2 prep 142 (under restoration)
2017 BMW i3 "Charged Professional" 94Ah
2024 VW id.buzz Pro

Used to own:
2001 Renault Matra Grand Espace "The Race" V6 24v
1997 Renault Matra Espace 2.0 8V
1987 Renault Matra Espace J11 2.2
Oetker
YaBB God
*****
Posts: 1097



« Reply #14 on: September 03, 2008, 11:29:30 pm »

Lots of things are coming to my mind.
Anything that wil wear has to be on stock
This is for the 2.2
All engineseals, waterpump, valveseals, rubbers for the enginemounting,radiator,waterhoses, frontscreen, clutchplate complete, lining roof/window, steering all components.
There is a lot more I can think of, but it may be better to find a spare car and rip it to parts.
Logged

I feel like Jonah, only my fish looks different.
Murena 2.2 Red 1982. Murena 1.6 black on places.
Pages: [1] 2 3 ... 5 Print 
« previous next »
Jump to: